Tags: Snapper7  75mm  Micro  FPV  Racer  Quadcopter  (Flysky  Receiver  Edition) 

Features:

Main Features:
● Multi-flight modes to choose: macro / AIR / ANGLE
● Powerful brushless motor and ESC 
● CNC aluminum alloy propeller guard
● BetaFlight OSD to get RSSI, voltage and other information from your goggles
● Use OSD to adjust the flight controller settings and the PID 
● Compatible Flysky AFHDS/ AFHDS-2A Receiver 
● Full telemetry function ready
● Head lights ready
● Adjustable camera angle 
● Real Bind and Fly version

Specifications:

Snapper7 75mm Micro FPV Racer Quadcopter  (Flysky Receiver Edition)

Wheelbase: 75mm
Propeller: 40mm 3 - blade propeller ( 4 CW + 4 CCW )

Crazybee F3 Flight Controller
Firmware: Crazybee BetaFlight 3.3.0 
MCU: STM32F303CCT6 ( 72MHz, 256K flash )
Sensor: MPU6000 ( SPI connection )
Power supply: 1S battery input ( DC 3.5 - 4.35V )
Built-in 5A BLHeli - S 4-in-1 ESC Dshot600 ready
Built-in BetaFlight OSD ( SPI control )
Built-in current meter ( max 14A, could be modified to 28A by replace resistor )
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHeli - S pass-through ready
Board size: 28.5 x 28.5mm
Board weight: 3.5g
Heading LED ready

Onboard 5A 4-in-1 ESC 
Power supply: 1S LiPo / LiPo HV ( 4.2V / 4.35V )
Continuous current: 5A 
Peak current: 6A ( 3 seconds )
BLHeli suite programmable
Factory firmware: O-L-5-REV16 - 6.HEX
Motor connector: JST PH1.25 3pin
Signal support: DShot150 / DShot300 / DShot600 / Oneshot125 / Multishot / PWM

Onboaed Flysky Receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch (AFHDS) or 14ch (AFHDS-2A)
No ground interference (Transmitter and receiver 1 m from the ground): 300m
Failsafe support
 

Video Transmitter: 
Output power: 25mW
Frequency: 48CH 
With raceband: 5474 - 5945MHz
Input voltage: 3.3 - 5.5V
Current consumption: 300mA

700TVL Camera
Field of view: 120-degree
Video format: NTSC
Antenna: RG178 antenna
Size: 13.9 x 12.0mm ( L x W )
Weight: 3g

Includes/Requires:

Includes:
1 x drone
1 x Crazybee F3 Flight control (built-in ESC, OSD, receiver, current sensor) 
1 x 5.8g 48CH 25MW VTX +700TVL 1/4 CMOS camera
1 x USB charger 
1 x screw driver
1 x propeller remover
4 x SE0703 KV19000  brushless motors
4 x 40mm cw/ccw  3-blade propellers


Requires:
1 x 1S Lipo battery (recommended type: 450mah, 30C, size: about 60x18x7mm)


* Battery is NOT included, we provided 2 compatible connectors with the kit.